AGS-G1 · REV A IN DESIGN LOOKING FOR DESIGN PARTNERS

AGS-G1

Dual-port DroneCAN RTK GNSS module

One module serves two autopilot buses: it publishes RTK GNSS on two isolated CAN FD ports, each guarded in hardware. A pair of modules gives heading without a magnetometer. Nothing is built yet, so every value on this page is a design value or a target.

For integrators of redundant UAS, and of survey aircraft that carry magnetometers.

2 × CAN FD
ISOLATED PORTS · DESIGN
RTK
MULTI-BAND RECEIVER · DESIGN
PAIR
HEADING, NO MAGNETOMETER · DESIGN
1 Gbit
RAW RECORDER · DESIGN
SIGNED
FIRMWARE ONLY · DESIGN
THE MODULE

One antenna, two buses.

A drawing, not a photograph. Each port is its own CAN FD bus.

WHAT SETS IT APART
IN DESIGN

Designed for aircraft that cannot trust one bus.

TWO ISOLATED PORTS

GNSS on two CAN FD ports. Each has its own power stage, ground and transceiver, so a fault on one bus stays on that bus, and the module runs from either port's power.

A HARDWARE TRANSMIT GUARD

A MUTE input on each port lets the autopilot on that bus silence the module's port in hardware, without relying on the module's firmware.

HEADING FROM A PAIR

Two modules, strapped base and rover in the harness, report heading over DroneCAN without a magnetometer.

LOW-MAGNETIC BY DESIGN

Designed from low-magnetic parts. Every unit will be measured on the fluxgate bench we use for the AGS-M1, and no figure is published until the first one is.

INTERFERENCE REPORTED

Jamming state, antenna status, spoofing indicators and Galileo OSNMA status go to the autopilot, not only to a log. The receiver cannot flag spoofing already present at start-up, so a spoofing state of "none" must never be read as "authentic".

A RAW RECORDER

1 Gbit of flash records the receiver's raw observations independently of the autopilot, for post-processed positioning and a record of the RF environment.

SIGNED FIRMWARE

ArduPilot's secure bootloader is on by default, and the module runs only firmware signed with a key the bootloader holds. As standard, those are our key and ArduPilot's; on order, just your key and ours.

OPEN FIRMWARE, CLOSED HARDWARE

The firmware is ArduPilot's AP_Periph under GPLv3, and the board definition goes upstream to ArduPilot. The hardware design is ours.

WHY US

GNSS designed to fly beside a magnetometer.

An aircraft that carries a magnetometer needs everything near the sensor to add as little field as possible. Measuring that field is the work we already do with the AGS-M1.

THE AGS-M1 BOARD →
DESIGN VALUES

What it is designed to be.

DESIGN VALUES · REV A
PARAMETER VALUE EVIDENCE
GNSS
Receiver u-blox ZED-F9P-05B, multi-band RTK DESIGN
Heading From a pair of modules strapped base and rover, over DroneCAN; no magnetometer DESIGN
Timing PPS on each port as a differential pair, driven from the receiver's time pulse DESIGN
Authentication Galileo OSNMA status reported to the autopilot DESIGN
PORTS AND POWER
CAN ports Two CAN FD ports, each on two DroneCAN JST-GH connectors and a 7-pin aux connector DESIGN
Isolation Each port isolated from the other: its own power stage, ground and transceiver DESIGN
Transmit guard A MUTE input on each port silences that port in hardware DESIGN
Identity Node ID and base or rover role from a strap in the harness DESIGN
Supply 5 V DroneCAN bus power on each port, designed for 4.55–5.5 V at the connector; runs from either port DESIGN
Power About 1.5 W in typical use at 5.5 V, a design estimate DESIGN
RECORDING AND FIRMWARE
Raw recorder 1 Gbit for raw observations, independent of the autopilot; about 18 h at 1 Hz, estimated DESIGN
Interference Jamming state, AGC, spoofing indicators and antenna status sent to the autopilot DESIGN
Firmware ArduPilot AP_Periph, GPLv3; the board definition goes upstream DESIGN
Signed firmware Secure bootloader on by default, holding our key and ArduPilot's; on order, just your key and ours DESIGN
PHYSICAL
Form A bare board, conformal-coated, with no enclosure DESIGN
Antenna One non-magnetic SMA; the active antenna's supply is supervised for open and short DESIGN
Mass Target under 20 g DESIGN
Mounting Target 30.5 × 30.5 mm hole pattern, for M3 DESIGN
Magnetic signature Not yet measured. Every unit will be measured on our fluxgate bench OPEN
Operating temperature Not yet specified. A bench thermal test in still and moving air sets it OPEN
DESIGN a design value, target or estimate; nothing is built or measured yetOPEN not yet published
WHERE IT STANDS

From parts to a first unit.

Design started in October 2026. The main parts are chosen, and the schematic is the current step.

AGS-G1 · REV A

Gates

2 OF 7 CLOSED
  • Board definition builds, secure bootloader included2026-10-13 DONE
  • Main parts chosen2026-11-15 DONE
  • Schematic ACTIVE
  • Layout OPEN
  • First units built OPEN
  • Magnetic signature measured OPEN
  • Bench thermal test OPEN

We are looking for design partners.

Integrators who will help shape the module and test the first units. Tell us about your aircraft and its buses: king@airandgravity.com