FLIGHT CONTROL · CALGARY, ALBERTA IN DESIGN LOOKING FOR AN AUTOPILOT PARTNER

Redundant flight control for uncrewed aircraft.

A flight control system for larger uncrewed aircraft, designed so the aircraft keeps flying and holds its heading when one part fails or GNSS is not available. Two identical lanes run side by side under hardware arbitration. Heading comes from two different sources, fluxgate magnetometers and a pair of AGS-G1 modules, and each lane checks one against the other. A power board feeds the avionics and measures every current, propulsion included, and an independent containment unit, on a different processor from the lanes, can end a flight safely without them. It is in design: every statement on this page is a design intent, and nothing has flown.

Designed in Calgary, Alberta. We intend to build it in Canada.

DUAL
IDENTICAL LANES · DESIGN
HARDWARE
ARBITRATION · DESIGN
FLUXGATE
MAGNETIC HEADING · DESIGN
CAN
PRIVATE BUSES PER LANE · DESIGN
SEPARATE
CONTAINMENT UNIT · DESIGN
THE SYSTEM

Two lanes, and everything they share.

A drawing, not a photograph: of what it shows, only the AGS-M1 board is built. Each lane has its own buses. The nodes both lanes need sit on both lanes' system buses, with a guarded port for each.

HOW IT IS REDUNDANT
IN DESIGN

A fallback at every layer.

Each of these is in the design. None is built or flown yet.

TWO LANES

Two identical flight control lanes. One commands and the other stands by. A lane that fails takes itself out of command in hardware, and the other takes over.

HEADING FROM MAGNETICS

Fluxgate magnetometers, mounted away from the aircraft's own currents and read the way the AGS-M1 reads them, give a heading that needs neither GNSS nor a radio link.

HEADING FROM GNSS

A pair of AGS-G1 modules gives a second, independent heading, and each lane checks one source against the other. The GNSS heading needs both modules; without it, the lanes use magnetic heading.

THE LANE DECIDES

Each lane checks every heading it is given and falls back on its own. The companion computer never switches a lane's heading source.

CAN FIRST

Each lane has its own buses. Every node the two lanes share has a hardware transmit guard on each lane's port, so a fault on one bus is meant to stay on that bus.

POWER THAT HOLDS

A separate power board with independent battery inputs, and critical channels that stay on in hardware: no software can switch them off.

EVERY CURRENT MEASURED

Every channel's voltage and current is measured and time-aligned, so the magnetic effect of the aircraft's own currents can be taken out of the reading.

INDEPENDENT CONTAINMENT

A separate unit, on a different processor family with its own GNSS, barometer and power conversion, keeps the aircraft inside its declared area and can cut propulsion and deploy a parachute, independent of both lanes.

NAVIGATING BY THE FIELD

Position fixes from matching the measured magnetic field against published survey maps, for flight without GNSS. In design; nothing tested yet.

WHY US

Flight control built around the magnetometer.

An aircraft's own currents and parts disturb magnetic heading. We measure magnetic fields, so this design starts from the field: the magnetometers sit away from the aircraft's currents, the parts near them are low-magnetic, and every current the power board switches is measured, so that its field can be taken out of the reading.

THE AGS-M1 BOARD →
DESIGN VALUES

What it is designed to be.

Every row is a design intent or open. The numbers come when there is hardware to measure.

DESIGN VALUES · NOTHING BUILT YET
PARAMETER VALUE EVIDENCE
LANES
Lanes Two identical boards; each lane's identity is set by its harness DESIGN
Arbitration In hardware, in discrete logic, independent of the lane processors DESIGN
Processors A flight processor and an independent I/O processor on each lane DESIGN
Flight software ArduPilot in the design and its simulation so far; an autopilot partner's flight software can take its place DESIGN
SENSING
Inertial IMUs from more than one maker on each lane, on a heated mount DESIGN
Air data Barometers of different families, and a differential airspeed sensor, on each lane DESIGN
Magnetic heading External fluxgate magnetometers, read the way the AGS-M1 reads them; a lane magnetometer as fallback DESIGN
GNSS A pair of AGS-G1 modules, shared by both lanes over CAN DESIGN
BUSES
CAN Each lane has its own FD-capable CAN buses, one for actuators and one for shared nodes; no bus is shared between lanes DESIGN
Shared nodes A hardware transmit guard on each lane's port DESIGN
Lane to lane A differential serial link, off CAN DESIGN
Companion computer Ethernet and serial to each lane; off the flight-critical path DESIGN
POWER
Inputs Independent battery inputs, kept apart from inlet to bus DESIGN
Channels Protected, switched channels; critical channels on in hardware, with no software off DESIGN
Telemetry Voltage and current on every channel, time-aligned to the lanes DESIGN
Lighting Anti-collision lighting run by the power board, so it survives a lane fault DESIGN
CONTAINMENT
Independence A different processor family from the lanes; its own GNSS, barometer and power conversion DESIGN
Action Cuts propulsion through a hardware disable input that each ESC must provide, then deploys a parachute, with a two-stage arm and fire DESIGN
PHYSICAL
Mass, power and operating temperature Not yet published OPEN
DESIGN a design intent; nothing is built or measured yetOPEN not yet published
WHERE IT STANDS

From the sensors up.

We started with what we know best. The magnetometer board is built, the GNSS module is at its schematic, and the flight control lanes come next.

FLIGHT CONTROL SYSTEM

Gates

3 OF 10 CLOSED
  • Magnetometer board built and field-tested (AGS-M1)September 2026 DONE
  • Lane processor pin map builds with ArduPilot2026-10-12 DONE
  • Two-lane arbitration run in simulation2026-10-12 DONE
  • GNSS module schematic (AGS-G1) ACTIVE
  • An autopilot partner ACTIVE
  • Power board channel budget: drafted, awaiting approval ACTIVE
  • Lane schematic OPEN
  • First lane built OPEN
  • Power board and containment unit built OPEN
  • Two lanes tested together, in hardware OPEN
AUTOPILOT PARTNER

We're looking for an autopilot partner.

The flight control lanes are the next step, and we want to build them with a team that brings flight control software of its own. We are early: a partner shapes the lanes, their interfaces and the first flights.

What we bring

  • Redundant lane hardware, in design here: two lanes, hardware arbitration, and CAN buses with guarded shared nodes.
  • A precise fluxgate magnetometer board, the AGS-M1, built and field-tested as a magnetometer. Heading from it is in design.
  • GNSS position, heading and timing from a pair of AGS-G1 modules, in design.
  • A power board that measures every load, and an independent containment unit, in design.

What we're looking for

  • A team with flight control software of its own, to run on this hardware or to build its lanes' software with us.
  • Experience flying larger uncrewed aircraft.
  • An interest in building it in Canada.

Tell us about your autopilot.

What it flies, what it runs on, and what you would want from redundant hardware under it: king@airandgravity.com